PAGE

Sabado, Hulyo 12, 2014

BLOG 4 - ELECTRICAL CIRCUIT 1

THIS BLOG CONTAIN ABOUT SERIES AND PARALLEL RESISTOR


Resistors in Series

   Resistors are said to be connected in Series, when they are daisy chained together in a single line. Since all the current flowing through the first resistor has no other way to go it must also pass through the second resistor and the third and so on. Then, resistors in series have a Common Current flowing through them as the current that flows through one resistor must also flow through the others as it can only take one path.
Then the amount of current that flows through a set of resistors in series will be the same at all points in a series resistor network. For example:
series resistor current
 
In the following example the resistors R1, R2 and R3 are all connected together in series between points A and B with a common current, I flowing through them.

Series Resistor Circuit

resistors in series
 
As the resistors are connected together in series the same current passes through each resistor in the chain and the total resistance, RT of the circuit must be equal to the sum of all the individual resistors added together. That is
series resistance equation
and by taking the individual values of the resistors in our simple example above, the total equivalent resistance, REQ is therefore given as:

 REQ = R1 + R2 + R3 = 1kΩ + 2kΩ + 6kΩ = 9kΩ


Equivalent resistance  

Equivalent resistance of any number of resistors connected in series is the sum of the individual resistance.


Resistors in Parallel

Resistors are said to be connected together in “Parallel” when both of their terminals are respectively connected to each terminal of the other resistor or resistors. Unlike the previous series resistor circuit, in a parallel resistor network the circuit current can take more than one path as their are multiple nodes. Then parallel circuits are current dividers.
Since there are multiple paths for the supply current to flow through, the current is not the same at all points in a parallel circuit. However, the voltage drop across all of the resistors in a parallel resistive network is the same. Then, Resistors in Parallel have a Common Voltage across them and this is true for all parallel connected elements.
So we can define a parallel resistive circuit as one where the Resistors are connected to the same two points (or nodes) and is identified by the fact that it has more than one current path connected to a common voltage source. Then in our parallel resistor example below the voltage across resistor R1equals the voltage across resistor R2 which equals the voltage across R3 and which equals the supply voltage. Therefore, for a parallel resistor network this is given as:
parallel resistor voltage
 
In the following resistors in parallel circuit the resistors R1, R2 and R3 are all connected together in parallel between the two points A and B as shown.

Parallel Resistor Circuit

resistors in parallel
 
In the previous series resistor network we saw that the total resistance, RT of the circuit was equal to the sum of all the individual resistors added together. For resistors in parallel the equivalent circuit resistance RT is calculated differently.
Here, the reciprocal ( 1/R ) value of the individual resistances are all added together instead of the resistances themselves with the inverse of the algebraic sum giving the equivalent resistance as shown.

Parallel Resistor Equation

parallel resistance
 
Then the inverse of the equivalent resistance of two or more resistors connected in parallel is the algebraic sum of the inverses of the individual resistances. The equivalent resistance is always less than the smallest resistor in the parallel network so the total resistance, RT will always decrease as additional parallel resistors are added.
Parallel resistance gives us a value known as Conductance, symbol G with the units of conductance being the Siemens, symbol S. Conductance is the reciprocal or the inverse of resistance, ( G = 1/R ). To convert conductance back into a resistance value we need to take the reciprocal of the conductance giving us then the total resistance, RT of the resistors in parallel.
We now know that resistors that are connected between the same two points are said to be in parallel. But a parallel resistive circuit can take many forms other than the obvious one given above and here are a few examples of how resistors can be connected together in parallel.

Equivalent Conductance

Equivalent conductance of resistors connected in parallel is the sum of their individual conductance.

Equivalent Resistance

Equivalent resistance of two resistor is equal to the product of their resistance divided by their sum.


LABORATORY

Objective:
  • To measure the voltage and current in a resistor.

Materials:
  • DC Power Supply 

  • Digital Multimeter


  • Resistor

  • Breadboard 



Overview and learning 

   Last Monday we had our quiz it was about ohms law, kirchhoff’s current law (KCL) and kirchhoff’s voltage law (KVL). On the next day we had our laboratory experiment and some of our classmates discussed about bread boarding on how to use. My group mates also discussed about we had our experiment and use material such dc power supply, digital multi meter, connection wires, resistor and bread boarding. We measure voltage and current in order to know if it flows to the bread board. I also learned how to put a resistor and connecting wire in the bread board correctly. Last Wednesday our professor discussed about the series and parallel resistor and last Friday we had our seatwork and it was about parallel and series resistor.   



Sabado, Hulyo 5, 2014

BLOG 3 - ELECTRICAL CIRCUIT 1




THIS BLOG CONTAIN ABOUT NODE, BRANCHES, LOOP, KCL and KVL.



BRANCHES - represent a single element such a voltage source or a resistor.

NODE - is the point of conduction between two or more branches.

LOOP - is any closed path in a circuit.



Gustav Robert Kirchhoff.jpg
Gustav Kirchhoff
Gustav Kirchhoff
BornGustav Robert Kirchhoff
12 March 1824
Königsberg, Kingdom of Prussia
(present-day Russia)
Died17 October 1887 (aged 63)
Berlin, Prussia, German Empire
(present-day Germany)
ResidencePrussia/German Empire
NationalityPrussian
FieldsPhysics
Chemistry
InstitutionsUniversity of Berlin
University of Breslau
University of Heidelberg
Alma materUniversity of Königsberg
Doctoral advisorFranz Ernst Neumann
Doctoral studentsMax Noether
Ernst Schröder
Known forKirchhoff's circuit laws
Kirchhoff's law of thermal radiation
Kirchhoff's laws of spectroscopy
Kirchhoff's law of thermochemistry
Notable awardsRumford medal (1862)
Davy Medal (1877)


KIRCHHOFF’S LAW or (KCL) – state that the algebraic sum of current entering a node (or a closed boundary) is zero.


Mathematically, KCL implies that         

 

Where N is the number of branches connected to the node and in is the nth current entering (or leaving) the node.







KIRCHHOFF’S VOLTAGE LAW or (KVL) – states that the algebraic sum of all voltages around a closed path (or loop) is zero.



                                                         
Expressed mathematically, KVL states that

 

Where M is the number of voltages in the loop (or the number branches in the loop)  andVm is the mth voltage.



OVERVIEW:

       On Monday June 30, 2014 our professor Mr. Jay S Villan is not around in our class but they have a substitute professor to take in charge the class of Mr. Jay S. Villan. The take in charge professor give a seat work on our class. On Tuesday we have a laboratory class and our professor give a work to discuss the deferent color of resistor. We get the result of our group calculation using the only the solving and we get the result of the resistor using the digital multimeter. We compared the result using solving and the result of multimeter. The title of experiment in this laboratory experiment is resistor color code and measurement of resistance. On Wednesday this is the start of our discussion and the topic that discussed of our professor is all about node, branches, and loop and the kirchhoff’s law. On Friday our professor give another seat work and this seat work is so hard to solve and get the answer.













Sabado, Hunyo 28, 2014

BLOG 2 - ELECTRIC CIRCUITS 1

This blog contain about ohm’s law


What do you usually think when you are asked, what is ohm’s law? If you think of a difficult, boring, and useless topic then, you should think again. You know why? All of us should have knowledge of electrical quantities and unit, even the most common ones only, is important analyzing electrical circuits.

Understanding ohm’s law, although the three quantities, current, voltage, and resistance, are use differently, they related to its other this relationship is know us ohm’s law. Ohm's law state that the voltage V across a resistor is directly proportional to the current I flowing through the resistor.


The fundamental relationship between voltage, current and resistance - in an electrical circuit is called Ohm’s Law. All materials are made up from atoms, and all atoms consist of protons, neutrons and electrons. Protons have a positive electrical charge. Neutrons have no electrical charge while Electrons, have a negative electrical charge. Atoms are bound together by powerful forces of attraction existing between the atoms nucleus and the electrons in its outer shell.





Surface-mount technology - is a method for producing electronic circuits in which the components are mounted or placed directly onto the surface of printed circuit boards. An electronic device so made is called a surface-mount device.



Open circuit - an open circuit exists when there is a break or gap in the circuit.
Causes of open circuits;
  • ·        broken wire
  • ·         poor connection
  • ·         loose terminal
  • ·         blown fuse
  • ·         tripped circuit breaker
  • ·         faulty switch
  • ·         Blown globe





Short circuit - a short circuit exists when the original path of current flow is altered and a shorter than normal path for current flow exists.

Causes of short circuits;
  • ·         worn or damaged wiring insulation
  • ·         wire squashed or jammed between components
  • ·         tools dropped across or accidental contact between positive and negative
  • ·         incorrectly connected ammeter
  • ·         Active wire incorrectly connected or joined to neutral position




AN OVERVIEW FOR THIS WEEK

To start let's have a recap of what we did and learned for this week.

Every Monday, Wednesday and Friday is the class discussion and Tuesday is the laboratory.

Last Monday, June 23 2014 we had our class discussion. we tackled about Ohm's law and as what i had learned Ohm's law is a current directly proportional to the voltage and inversely proportional to the resistance.

In every daily living we are applying Ohm's law, though we did not recognized it but the fact is we applied circuits in our home the appliances that we are using as well as enjoying that makes our lives become more comfortable it has a current as well as voltage and it is important to know how it works.

On the following day our laboratory. It was Tuesday and our professor let us familiarized the different components ad equipment such as IC, digital multimeter, resistor, transistor and hindi ko na alam ang iba :) hahaha. After that we find the manufacturer, model number, type of power supply and sketch. 

Wednesday June 25, 2014 the class discussion again it was the continuation of last topic.